OpenVox D410P Zaptel en
From Wiki
Contents |
D410P User Manual
Chapter 1 Overview
1. What is D410P
D410P is a high-performance, cost-effective four span digital voice card. It provides compact and powerful interface to asterisk that can support E1/T1/J1 and PRI interface.
With the improved I/O speed, the card reduces CPU usage and increased card density per server. D410P is fully compatible with Asterisk application. The open source driver supports an API interface for custom application development.
D410P supports industry standard telephony and data protocols including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.
Other Features Include:
1) Supporting 3.3V and 5V PCI slots
2) High Performance PCI BusMaster with up to 2Kbytes FIFO
3) Be easy to install: Support wct4xxp driver included in original zaptel without any patch
Certificates: CE, FCC
Misc:
1) Temperature Operation: 0 to 50°C
2) Temperature Storage: - 65 to 125°C
3) Humidity:10 TO 90% NON-CONDENSING
4) Voltage:3.3V/5V
5) Power Dissipation Max:2.6W/3.9W
2. What is Asterisk:
The Definition of Asterisk is described as follow:
Asterisk is a complete PBX in software. It runs on Linux,BSD,Windows (emulated) and provides all of the features you would expect from a PBX and more. Asterisk does voice over IP in four protocols, and can interoperate with almost all standards-based telephony equipment using relatively inexpensive hardware.
Asterisk provides:
1) Voicemail services with Directory
2) Call Conferencing
3) Interactive Voice Response
4) Call Queuing
5) Support for three-way calling, caller ID services
6) ADSI, IAX, SIP, H.323, MGCP and SCCP/Skinny.
Chapter 2 Card Installation and Configuration
1. Hardware Installation and Setup
Before inserting the D410P card in to PCI slot, customer should set the jumpers correctly. Please check:
1) SPAN Type Setup
P5 controls the function of each span at E1 or T1 mode.
2) If using timing cable, adjust jumper J916 to Closed status(PLL), and connect two card by timing cable. Make sure the cable connecting Input on first card and Output on second card; Otherwise, Use default setting (Open status(CRY)). More details, please refer this url: http://bbs.openvox.cn/viewthread.php?tid=874&extra=page%3D1
3) Software Installation and Setup
D410P supports original zaptel wct4xxp driver. Customers can download zaptel driver from asterisk.org. There are few steps to install wct4xxp drivers.
Checking the hardware by command: lspci -v
Downloading and compiling, to make the asterisk and zaptel running, users have to download libpri, zaptel and asterisk. For more details about source of these packages, please visit:www.asterisk.org.
Note:
If there is no kernel source in the system, user should install them. User can run yum again: yum install kernel-devel. If the kernel is smp kernel, please run this command: yum install kernel-smp-devel.
Checking and installing these packages before proceeding with the installation of Asterisk.
If you want to install Dahdi and asterisk, please refer this link:
http://bbs.openvox.cn/viewthread.php?tid=575&extra=page%3D2
rpm -q bison rpm -q bison-devel rpm -q ncurses rpm -q ncurses-devel rpm -q zlib rpm -q zlib-devel rpm -q openssl rpm -q openssl-devel rpm -q gnutls-devel rpm -q gcc rpm -q gcc-c++
if one of the packages is missed, please install that as follow:
yum install bison yum install bison-devel yum install ncurses yum install ncurses-devel yum install zlib yum install zlib-devel yum install openssl yum install openssl-devel yum install gnutls-devel yum install gcc yum install gcc-c++
Here，assuming the three packages are stored in /usr/src directory. Customers compile those packages as following in ORDER:
1. Installing libpri:
cd /usr/src/libpri make clean make make install
2. Installing zaptel
cd /usr/src/zaptel make clean make make install
3. Installing asterisk
cd /usr/src/asterisk make clean make make install
Loading wct4xxp driver for D410P, editing zaptel.conf:
span=1,1,1,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" span=2,2,1,ccs,hdb3 # termtype: te bchan=32-46,48-62 dchan=47 # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" span=3,3,1,ccs,hdb3 # termtype: te bchan=63-77,79-93 dchan=78 # Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" span=4,4,1,ccs,hdb3 # termtype: te bchan=94-108,110-124 dchan=109 # Global data loadzone = us defaultzone = us
modprobe zaptel modprobe wct4xxp ztcfg –vvvvvvvv dmesg
Configuring zapata.conf and extensions.conf
1) Edit the zapata.conf by vi /etc/asterisk/zapata.conf:
[channels] context=from-pstn switchtype=euroisdn pridialplan=national signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 immediate=no callprogress=no callerid=asreceived group=1 signalling=pri_cpe channel => 1-15,17-31 group=2 signalling=pri_cpe channel => 32-46,48-62 group=3 signalling=pri_cpe channel => 63-77, 79-93 group=4 signalling=pri_cpe channel => 94-108,110-124
2) Edit the extensions.conf by vi /etc/asterisk/extensions.conf:
[from-pstn] exten => s,1,Answer() // answer the inbound call exten => s,n,Playback(cc_welcome) // please message exten => s,n,Hangup() [from-internal] // test outbound calls exten => 200,1,Dial(zap/1/outgoing_number) // dial 200 to dialout from zap 1 exten => 200,2,Hangup
3) Starting asterisk by asterisk –vvvvvvvgc
after starting asterisk, please check the zap channels. Under asterisk console,
check the status of card by these commands:
zap show channels. It should shows zap channels, if the zapata.conf is correct. pri show spans. It will show the status of the physical connections. MUST be UP, active to make calls.
Chapter 3 References
www.openvox.cn
www.digium.com
www.asterisk.org
www.voip-info.org
www.asteriskguru.com
Test environment
Centos-5.0 Kernel version: 2.6.18-8.el5 Zaptel: 1.4.XXX Asterisk: 1.4.XXX Hardware: OpenVox D410P
